Test drove vehicle and scanned for codes. Found multiple codes including P0130- 02 sensor circuit(bank1sensor1), P0150- 02 sensor circuit (bank2sensor1), P144A- evap system purge vapor line restricted, and P1450- unable to bleed up fuel tank vacuum. After performing system diag found both front bank 02 sensors worn out and not reading correctly. Also found evap purge valve sticking at times. During diagnosis found the spark plugs appeared worn out and due for replacement. Suggest replacing known faulty parts, clearing trouble codes, and rechecking vehicle operation.
INSTALL BOTH UPSTREAM 02 SENSORS
CANISTER PURGE SOLENOID – Remove & Replace – Purge Valve – [Includes: Validation with use of Scan Tool.] – [Includes: Component test.]
SPARK PLUGS – Remove & Replace – F150,5.4L Eng
Inspect hoses and clamps. Pressure test cooling system. Flush engine, radiator, and heater core in both directions. Bring antifreeze to -35 degrees. PH balance coolant to between 9.8 to 10.5. Check thermostat and electric cooling fan operation. Chec
Shawn D. gave our service a 5 star review on 10/18/2022
VERIFIED CUSTOMERS CONCERN AND FOUND SERVICE 4WD LIGHT ILLUMINATED. TESTED 4WD SYSTEM AND FOUND TO BE WORKING PROPERLY. SCANNED TRANSFER CASE MODULE AND FOUND CODE C0395-FRONT DIFFERENTIAL ACTUAR CIRCUIT. INSPECTED WIRING FROM FRONT DIFFERENTAL AND FOUND PLUG AT PASSENGER FRAME RAIL NOT FULLY PLUGGED IN. PLUGGED CONNECTOR IN FULLY AND TEST DROVE VEHICLE AND SERVICE 4WD DID NOT RETURN.
Tom S. gave our service a 5 star review on 10/11/2022
Test drove vehicle and scanned for codes. Found P2181- performance malfunction in cooling system. Visually inspected cooling system, electrical circuits and connections for any obvious faults and found none. Observed scan tool data while vehicle warmed up to normal operating temp and found cooling system never reached normal operating temps in specified time period. Suggest thermostat replacement, clearing trouble code, and rechecking cooling system performance.
THERMOSTAT &/OR GASKET – Remove & Replace – 1.8L Eng
Inspect hoses and clamps. Pressure test cooling system. Flush engine, radiator, and heater core in both directions. Bring antifreeze to -35 degrees. PH balance coolant to between 9.8 to 10.5. Check thermostat and electric cooling fan operation. Chec
Changed Motor Oil & Replaced Filter, Added 5 QTS Synthetic Motor Oil, Lube Chassis, Check all Fluid Levels
ALTERNATOR DRIVE BELT – Remove & Replace – In-Line4,Gas w/Air Cond – [Includes: Move Lock Carrier to service position.] – [Includes: Serpentine and V-Belt type Belt(s).]
Mira L. gave our service a 5 star review on 10/4/2022
Test drove vehicle and scanned for codes. Found P2181- performance malfunction in cooling system. Visually inspected cooling system, electrical circuits and connections for any obvious faults and found none. Observed scan tool data while vehicle warmed up to normal operating temp and found cooling system never reached normal operating temps in specified time period. Suggest thermostat replacement, clearing trouble code, and rechecking cooling system performance.
THERMOSTAT &/OR GASKET – Remove & Replace – 1.8L Eng
Inspect hoses and clamps. Pressure test cooling system. Flush engine, radiator, and heater core in both directions. Bring antifreeze to -35 degrees. PH balance coolant to between 9.8 to 10.5. Check thermostat and electric cooling fan operation. Chec
Changed Motor Oil & Replaced Filter, Added 5 QTS Synthetic Motor Oil, Lube Chassis, Check all Fluid Levels
ALTERNATOR DRIVE BELT – Remove & Replace – In-Line4,Gas w/Air Cond – [Includes: Move Lock Carrier to service position.] – [Includes: Serpentine and V-Belt type Belt(s).]
Mira L. gave our service a 5 star review on 10/4/2022