Nissan Archives - Page 2 of 5 - Chicago Driveline Inc

2009 Nissan Xterra
Mileage
219,833
Service Date
7/10/2023
Services Performed
DIFF FLUID CHANGE FRT AND REAR
Changed Motor Oil & Replaced Filter, Added 5 QTS Synthetic Motor Oil, Lube Chassis, Check all Fluid Levels
DRAIN / FILL FRONT DIFF FLUID
DRAIN FILL REAR DIFF FLUID
Bill H. gave our service a 5 star review on 7/11/2023
2013 Nissan Sentra
Mileage
48,258
Service Date
1/26/2023
Services Performed
Checked for cable movement at trans and all is hooked up and working proper. Needs new transmission. Check dealer for warranty. Called Nissan vehicle has no warranty.
TRANSAXLE ASSEMBLY – Removal & Installation – Automatic CVT Trans w/o Powertrain Assembly Removal – [DOES NOT include wheel alignment.]
DEALER PROGRAMMING UNIT
Lorraine / Hugh O. gave our service a 5 star review on 1/28/2023
2017 Nissan Rogue
Mileage
89,680
Service Date
11/16/2022
Services Performed
AFTER TEST DRIVING AND INSPECTING ON HOIST FOUND BOTH LOWER BALL JOINTS CAUSING NOISE CONCERNS.
CONTROL ARM – Remove & Replace –
TWO Wheel Alignment. Warranty-30 Days
CK VEHICLE SHAKES / VIBRATES WHEN FAN IS ON
Changed Motor Oil & Replaced Filter, Added 5 QTS Synthetic Motor Oil, Lube Chassis, Check all Fluid Levels
MAINT ROTATE TIRES (FREE/W TIRES PURCHASED HERE)
CABIN AIR FILTER – Remove & Replace
INSTALL NEW WIPERS
John S. gave our service a 5 star review on 11/16/2022
2013 Nissan Altima
Mileage
129,800
Service Date
11/15/2022
Services Performed
CK BRAKES MAKING NOISE PEDAL SOFT
INSTALL REAR PADS / ROTORS
INSTALL WARRANTY BATTERY
Herman / Kim D. gave our service a 5 star review on 11/16/2022
2010 Nissan Altima
Mileage
112,165
Service Date
11/3/2022
Services Performed
ck exhaust making noise
REC REPLACING RUSTED PRETTY BAD CUSTOMER ADVISED AND DECLINED ANY FURTHER SERVICES AT THIS TIME.
FOUND BROKEN AND CAUSING NOISE CONCERNS
Kejai M. gave our service a 5 star review on 11/3/2022
2013 Nissan Sentra
Mileage
54,372
Service Date
9/13/2022
Services Performed
VERIFIED CUSTOMERS CONCERN AND FOUND CHECK ENGINE LIGHT ILLUMINATED. SCANNED VEHICLE AND FOUND CODE P1217-ENGINE OVER TEMPERATURE. PRESURE TESTED COOLING SYSTEM AND FOUND RADIATOR LEAKING AT PASSENGER SIDE LOWER TANK. REPLACED RADIATOR ,COOLING SENSOR, AIR FILTER AND BATTERY. TEST DROVE VEHICLE AND NO MORE LEAKS PRESENT. AND VEHICLE NOW ACCELARATES.
RADIATOR – Remove & Replace
INSTALL BATTERY & AIR FILTER
Lorraine O. gave our service a 5 star review on 9/15/2022
2009 Nissan Xterra
Mileage
116,019
Service Date
8/30/2022
Services Performed
Test Drove Vehicle And Heard Tire Noise And No Vibration At All Speeds..Tires On Inside Tread Have High And Low Spots Causing Noise. Recommend 4 Tires,Shocks Struts and Align as a Starting Point JW
Remove Tire from Vehicle, Inspect & Repair as Nec.
Examine the suspension bushings for cracking, deterioration and wear. With the vehicle raised, inspect for binding / movement at the ball joints or struts while turning the steering wheel lock-to-lock. … Inspect the shocks for damage and fluid leaks. And all tie rods with digital print out.
Frank O. gave our service a 5 star review on 8/31/2022
2004 Nissan Frontier
Mileage
137,515
Service Date
8/18/2022
Services Performed
ck driveshaft slight clicking noise poss center bearing
PROPELLER SHAFT – Removal & Installation – RWD
Turner T. gave our service a 5 star review on 8/27/2022
2009 Nissan Xterra
Mileage
209,142
Service Date
8/22/2022
Services Performed
CK ROARING NOISE AT 30 MPH POSS DIFF NOISE
RING GEAR & PINION – Remove & Replace – C200K 4WD
New gear sets MUST be broken in correctly to prevent damage. Not following proper break-in procedures will lead to overloading and overheating the ring and pinion as well as breaking down and ruining the gear oil. Not following proper break-in procedures can be determined during inspection and will void the warranty. Please follow the below guidelines to ensure a proper break-in and long life of your gears. • Only use high quality gear oils. • On initial run, drive lightly for 15 to 20 minutes then stop to allow differential to cool completely for 20 to 25 minutes. • Avoid towing and heavy acceleration, as well as vary speeds every 5 to 10 minutes while driving on highways. • Drive conservatively and do not drive more than 50 miles at a time without allowing a cool cycle during the first 500 miles following installation. • After completing initial break-in, change gear oil at 500 miles. Small metal particles are normal and gear oil will typically be black. Excessive metal in gear oil should be reviewed by a competent differential mechanic to ensure safety of internal parts. Post gear oil change and initial break-in: Towing. • First time towing should be limited to light load for no more than 15 miles, then allow differential to cool completely for 20 to 25 minutes. • Repeat this procedure for first 45 miles of towing for full break-in of gears for towing vehicles.**NOTE**After market Gears are sometimes louder then original equipment gears this is normal. Commercial Vehicle WARRANTIES 90 DAYS PREMATURE OVERLOADING AND IMPROPER BREAK-IN WILL CAUSE GEAR OIL BREAKDOWN AND MAY RESULT IN RING AND PINION FAILURE VOIDING THE GEAR WARRANTY!
New gear sets MUST be broken in correctly to prevent damage. Not following proper break-in procedures will lead to overloading and overheating the ring and pinion as well as breaking down and ruining the gear oil. Not following proper break-in procedures can be determined during inspection and will void the warranty. Please follow the below guidelines to ensure a proper break-in and long life of your gears. • Only use high quality gear oils. • On initial run, drive lightly for 15 to 20 minutes then stop to allow differential to cool completely for 20 to 25 minutes. • Avoid towing and heavy acceleration, as well as vary speeds every 5 to 10 minutes while driving on highways. • Drive conservatively and do not drive more than 50 miles at a time without allowing a cool cycle during the first 500 miles following installation. • After completing initial break-in, change gear oil at 500 miles. Small metal particles are normal and gear oil will typically be black. Excessive metal in gear oil should be reviewed by a competent differential mechanic to ensure safety of internal parts. Post gear oil change and initial break-in: Towing. • First time towing should be limited to light load for no more than 15 miles, then allow differential to cool completely for 20 to 25 minutes. • Repeat this procedure for first 45 miles of towing for full break-in of gears for towing vehicles.**NOTE**After market Gears are sometimes louder then original equipment gears this is normal. Commercial Vehicle WARRANTIES 90 DAYS PREMATURE OVERLOADING AND IMPROPER BREAK-IN WILL CAUSE GEAR OIL BREAKDOWN AND MAY RESULT IN RING AND PINION FAILURE VOIDING THE GEAR WARRANTY!
Bill H. gave our service a 5 star review on 8/23/2022
2013 Nissan Altima
Mileage
126,101
Service Date
6/13/2022
Services Performed
Changed Motor Oil & Replaced Filter, Added 4 QTS Blended Motor Oil, Lube Chassis, Check all Fluid Levels
WILL NEED REAR SOON
Herman / Kim D. gave our service a 5 star review on 6/13/2022

Nissan

We Service and Repair all Nissan cars