CRM Mitchell1, Author at Chicago Driveline Inc

2017 Jeep Cherokee
Mileage
37,667
Service Date
8/31/2022
Services Performed
VEHICLE RUNS FINE IT'S NOT TIME FOR A TUNE-UP WITH SUCH LOW MILAGE ON VEHICLE. EVERYTHING CHECKED OUT GOOD AT THIS TIME.
Changed Motor Oil & Replaced Filter, Added 5 QTS Synthetic Motor Oil, Lube Chassis, Check all Fluid Levels
INSTALL NEW AIR FILTER
Linda M. gave our service a 5 star review on 8/31/2022
2007 Chevrolet Tahoe
Mileage
128,663
Service Date
8/31/2022
Services Performed
Test drove vehicle and scanned for codes. Found P0171- fuel trim ,Ean bank 1, and P0174- fuel trim lean bank 2. Performed diag and found mass airflow sensor specs below threshold. Test fuel pressure and found at lower end of spec, but in range. Recommend starting with replacing worn mass airflow sensor and performing fuel system cleaning, resetting fuel trims, and clearing codes.
MASS AIR FLOW SENSOR – Remove & Replace
The Carbon Clean System is a technologically advanced method for cleaning and de-carbonizing harmful fuel system contaminants from gasoline engines,Clean Throttle body And Fuel Tank Additive.
CK E-BRAKE CABLE HANGING IN REAR BY DIFFERENTIAL
George G. gave our service a 5 star review on 9/1/2022
2009 Nissan Xterra
Mileage
116,019
Service Date
8/30/2022
Services Performed
Test Drove Vehicle And Heard Tire Noise And No Vibration At All Speeds..Tires On Inside Tread Have High And Low Spots Causing Noise. Recommend 4 Tires,Shocks Struts and Align as a Starting Point JW
Remove Tire from Vehicle, Inspect & Repair as Nec.
Examine the suspension bushings for cracking, deterioration and wear. With the vehicle raised, inspect for binding / movement at the ball joints or struts while turning the steering wheel lock-to-lock. … Inspect the shocks for damage and fluid leaks. And all tie rods with digital print out.
Frank O. gave our service a 5 star review on 8/31/2022
2004 Nissan Frontier
Mileage
137,515
Service Date
8/18/2022
Services Performed
ck driveshaft slight clicking noise poss center bearing
PROPELLER SHAFT – Removal & Installation – RWD
Turner T. gave our service a 5 star review on 8/27/2022
2017 Ford F-150
Mileage
55,975
Service Date
8/25/2022
Services Performed
CHECK ALL- FLUIDS , FILTERS , HOSES , BELTS , TIRES , BRAKES BATTERY ,ETC
CK BRAKES WORN HAD AT FORD THEY RECOMMENDED BRAKES
INSTALL REAR PADS / ROTORS W/ELEC E-BRAKE
INSTALL CABIN FILTER
CK ALL FLUIDS FORD RECOMMENDED FLUSHES??
TRANSFER CASE DRAIN / FILL FLUID
INSTALL NEW AGM BATTERY
Dan L. gave our service a 5 star review on 8/26/2022
2012 Honda Accord
Mileage
56,090
Service Date
8/24/2022
Services Performed
VERIFIED CUSTOMERS CONCERN AND FOUND REAR VIEW MIRROR OFF WINDSHIELD. UPON INSPECTION FOUND MOUNTING SCREWS MISSING AND GLUE ON MOUNTING POINTS REMOVED GLUE AND FABRICATED MOUNTING HARDWARE AND REINSTALLED MIRROR.
Bill S. gave our service a 5 star review on 8/25/2022
2009 Nissan Xterra
Mileage
209,142
Service Date
8/22/2022
Services Performed
CK ROARING NOISE AT 30 MPH POSS DIFF NOISE
RING GEAR & PINION – Remove & Replace – C200K 4WD
New gear sets MUST be broken in correctly to prevent damage. Not following proper break-in procedures will lead to overloading and overheating the ring and pinion as well as breaking down and ruining the gear oil. Not following proper break-in procedures can be determined during inspection and will void the warranty. Please follow the below guidelines to ensure a proper break-in and long life of your gears. • Only use high quality gear oils. • On initial run, drive lightly for 15 to 20 minutes then stop to allow differential to cool completely for 20 to 25 minutes. • Avoid towing and heavy acceleration, as well as vary speeds every 5 to 10 minutes while driving on highways. • Drive conservatively and do not drive more than 50 miles at a time without allowing a cool cycle during the first 500 miles following installation. • After completing initial break-in, change gear oil at 500 miles. Small metal particles are normal and gear oil will typically be black. Excessive metal in gear oil should be reviewed by a competent differential mechanic to ensure safety of internal parts. Post gear oil change and initial break-in: Towing. • First time towing should be limited to light load for no more than 15 miles, then allow differential to cool completely for 20 to 25 minutes. • Repeat this procedure for first 45 miles of towing for full break-in of gears for towing vehicles.**NOTE**After market Gears are sometimes louder then original equipment gears this is normal. Commercial Vehicle WARRANTIES 90 DAYS PREMATURE OVERLOADING AND IMPROPER BREAK-IN WILL CAUSE GEAR OIL BREAKDOWN AND MAY RESULT IN RING AND PINION FAILURE VOIDING THE GEAR WARRANTY!
New gear sets MUST be broken in correctly to prevent damage. Not following proper break-in procedures will lead to overloading and overheating the ring and pinion as well as breaking down and ruining the gear oil. Not following proper break-in procedures can be determined during inspection and will void the warranty. Please follow the below guidelines to ensure a proper break-in and long life of your gears. • Only use high quality gear oils. • On initial run, drive lightly for 15 to 20 minutes then stop to allow differential to cool completely for 20 to 25 minutes. • Avoid towing and heavy acceleration, as well as vary speeds every 5 to 10 minutes while driving on highways. • Drive conservatively and do not drive more than 50 miles at a time without allowing a cool cycle during the first 500 miles following installation. • After completing initial break-in, change gear oil at 500 miles. Small metal particles are normal and gear oil will typically be black. Excessive metal in gear oil should be reviewed by a competent differential mechanic to ensure safety of internal parts. Post gear oil change and initial break-in: Towing. • First time towing should be limited to light load for no more than 15 miles, then allow differential to cool completely for 20 to 25 minutes. • Repeat this procedure for first 45 miles of towing for full break-in of gears for towing vehicles.**NOTE**After market Gears are sometimes louder then original equipment gears this is normal. Commercial Vehicle WARRANTIES 90 DAYS PREMATURE OVERLOADING AND IMPROPER BREAK-IN WILL CAUSE GEAR OIL BREAKDOWN AND MAY RESULT IN RING AND PINION FAILURE VOIDING THE GEAR WARRANTY!
Bill H. gave our service a 5 star review on 8/23/2022
2013 Hyundai Sonata
Mileage
112,618
Service Date
8/19/2022
Services Performed
CK KNOCKING NOISE ON BUMPS
CK BRAKES MAKES NOISE WHEN BRAKING
INSTALL FRT PADS / ROTORS
INSTALL REAR PADS / ROTORS
INSTALL L/FRT LOW BALL JOINT AND FRT LINK PINS
INSTALL OUTER TIERODS
TWO Wheel Alignment. Warranty-30 Days
INSTALL CABIN FILTER
Changed Motor Oil & Replaced Filter, Added 5 QTS Synthetic Motor Oil, Lube Chassis, Check all Fluid Levels
Daniel V. gave our service a 5 star review on 8/20/2022
2010 Chevrolet Silverado
Mileage
138,625
Service Date
8/17/2022
Services Performed
Changed Motor Oil & Replaced Filter, Added 4 QTS Blended Motor Oil, Lube Chassis, Check all Fluid Levels
Mount and balance four tire/wheel assemblies.
Tire disposal fee
Tire user fee
AFTER DIAG SYSTEM HAS MULTIPLE CODES (WOW) P0011 , PO449 ,PO454 , PO455 , PO521 , P219A , P219B , P2270 , P2271
THIS WOULD BE A STARTING POINT FOR ALL CODES PRESENT DURING DIAG.
Jeff / Stacey M. gave our service a 5 star review on 8/17/2022
2014 Chevrolet Silverado 1500
Mileage
104,552
Service Date
8/16/2022
Services Performed
CONFIRMED CODE R/F ABS WHEEL SENSOR BAD NO SIGNAL. L/F WHEEL SIGNAL WOULD GO IN AND OUT ON SCANNER WHEN TEST DRIVING VEHICLE REC REPLACING BOTH FRONT HUB BEARINGS AND RETEST VEHICLE.
REPLACED BEARINGS ALL WORKING FINE AS OF NOW NO CODES PRESENT AFTER TEST DRIVING.
FOUND LEAKING GREASE WHEN DOING WHEEL BEARINGS.
Danny B. gave our service a 5 star review on 8/16/2022

CRM Mitchell1

We Service and Repair all CRM Mitchell1 cars